RRP $679.69
$611.70
SAVE $67.99 (10%)
In Stock

More info.

Make 4 interest-free payments of $152.93 fortnightly and receive your order now.

Components

Calculate Shipping



Pickup Instore - $0.00
Please await contact from a Sales Representative at OzLED to confirm the order is ready to be collected. Contact attempts will be made by phone and email.

bluePrint Control System

Improve Officer Safety and Efficiency Officers are constantly occupied with technology and other distractions that require a shift in concentration and a refocus of the eyes and hands. The bluePRINT Control System allows officers to stay focused on the task at hand while keeping their eyes on the road and hands on the wheel. Light and siren configurations are pre-programmed and prioritized to respond to emergency situations without the officer having to hastily determine which buttons and switches to activate while driving. Eliminate Point-to-Point Wiring Each of these modules communicates over a serial data bus (multiplex). The Central Controller, the Remote Nodes, the Input Node, and the 200R Sirens all share a single wire bus that can run the length of the vehicle. This eliminates the need for point-to-point wiring between lighting and siren components. Separate LIN data bus connections are provided for plug-and-play compatibility with existing SoundOff Signal Exterior Lightbars, nForce Interior Lightbars/Traffic Arrows, and Siren components. Improve System Reliability and Convenience Current switching within the Central Controller and Remote Nodes uses Solid State Transistors to eliminate mechanical switching. Relays and other electro-mechanical components are often the most frequent failure within a switching system. Most are incapable of detecting faults and can be damaged by wiring faults such as an over-current. Solid State switching offers the advantage of no moving parts, no arc bridging, and self-diagnostic capabilities.   https://www.youtube.com/watch?v=c2E9fxdKXLE

Central Controller Specs

Input Voltage 10-16Vdc (Negative Ground) Maximum Load Current 100 Amps Outputs (Sum of ALL used Outputs shall Not Exceed 100Amps) 4x 10AMP Fused Battery 8x 10AMP Solid State, Switched 12x 5AMP Solid State, Switched IGN ON: Standby Current 140mA IGN OFF: Sleep Current 0.34mA Inputs 1x Ignition Input Active High Reverse Polarity Protection Not Protected (Reverse Polarity will Destroy the Devices) Transient Protection Protected High Voltage Protection >16V; High Voltage Error Code Set Low Voltage Protection <9V; Low Voltage Error Code Set Operating Temp -40° C to +65° C Dimensions 7€³ x 6.25€³ x 1€³ Weight, Boxed 1 lb. 7 oz. Weight, Device Only 14.9 oz. Valid Integration Threshold - High >8.5V The Central Controller is not waterproof. Install in a protected location away from excessive heat and moisture.

Control Panel Specs

Input Voltage 10-16Vdc (Negative Ground) Sleep Current 8 mA Inputs 1x 3pin MIC Input Reverse Polarity Protection Protected Transient Protection Protected High Voltage Protection Protected Low Voltage Protection Protected Operating Temp -40° C to +65° C Dimensions 6.9€³ H x 3.5€³ W x 1.2€³ D Weight, Boxed 1.3 lb. Weight, Device Only 1.1 lb. The control panel is not waterproof. Install in a protected location away from excessive heat and moisture.

Input Node Specs

Input Voltage 10-16Vdc (Negative Ground) Maximum Input Current N/A Outputs (Sum of ALL used Outputs Shall Not Exceed 100Amps) None IGN ON: Standby Current 30 mA IGN OFF: Sleep Current 0.20 mA Inputs 20 Total 13x Active High/Low Inputs 7x Active High Inputs 1x Local IGN Input (Local Sleep Mode) Reverse Polarity Protection Protected Transient Protection Protected High Voltage Protection >16V; High Voltage Error Code Set Low Voltage Protection <9V; Low Voltage Error Code Set Operating Temp -40° C to +65° C Dimensions 3.5€³ x 3.5€³ x .75€³ Weight, Boxed 5 oz. Weight, Device Only 4 oz. Valid Input Threshold - High >7.5V Valid Input Threshold - Low <1.5V The Input Node is not waterproof. Install in a protected location away from excessive heat and moisture.

Remote Node Specs

Input Voltage 10-16Vdc (Negative Ground) Maximum Input Current 50 Amps (30Amps at 85° C) Outputs (Sum of ALL used Outputs shall Not Exceed 50Amps) 4x 10AMP Solid State, Switched 6x 5AMP Solid State, Switched IGN ON: Standby Current 60mA IGN OFF: Sleep Current 0.34mA Inputs 4x Total 3x Active High/Low Inputs *1x Active high/low Input w/ System Wake up Reverse Polarity Protection Not Protected (Reverse Polarity will Destroy the Devices) Transient Protection Protected High Voltage Protection >16V; High Voltage Error Code Set Low Voltage Protection <9V; Low Voltage Error Code Set Operating Temp -40° C to +65° C (85° C max current = 30Amps) Dimensions 6€³ x 3.4€³ x .8€³ Weight, Boxed 13.2 oz. Weight, Device Only 10.7 oz. Valid Input Threshold - High >8.0V Valid Input Threshold  - Low <1.5V Hermetically sealed providing protection in wet areas.

100 Watt Siren Specs

Input Voltage 10-16Vdc (Negative Ground) Maximum Input Current 8 Amps @ 13.6 Vdc (100W Speaker) Outputs 100W Sleep Current <1 mA Inputs 1x Horn Ring Input 1x Park Kill 1x CP Back Light 1x Radio Rebroadcast 1x PA High Voltage Protection 30Vdc will cause siren output to cease and will resume when system voltage is above 10.0 Volts. Low Voltage Protection <9.0 Volts will cause siren output to cease and will resume when system voltage is above 10.0 Volts. Operating Temp -40° C to +65° C Dimensions 2.3€³H x 5.4€³W x 4.6€³D Weight, Boxed 3 lbs. Weight, Device Only .93 lbs. Valid Input Threshold - High >10.6V - Park Kill, PTT, Aux, Horn Ring >9.0V - Primary/Secondary Backlight Valid Input Threshold -Low <0.6V 200R Siren is hermetically sealed, providing protection in wet areas.

100/200 Watt Siren/Switch Module Specs

Input Voltage 10-16Vdc (Negative Ground) Total Max Relay Current 100 Amps Siren Maximum Input Current 100W Speaker: 7 Amps @ 13.6 Vdc 100W Speakers (2x): 14 Amps @ 13.6 Vdc Siren Power Outputs 100 and 200 Watts Sleep Current <1 mA Inputs 1x horn ring input, 1x park kill, 1x CP back light, 1x radio rebroadcast and 1x PA High Voltage Protection >18 Vdc will cause siren output to cease, resume at normal Low Voltage Protection <9.0 volts will cause siren output to cease and will resume when system voltage is above 10.0 volts Operating Temp -40° C to +50° C Dimensions 2.62€³ H x 7.00€³ W x 6.51€³ D Valid Input Threshold: High >10.6 V - park kill, PTT, auxiliary, horn ring and >9.0 V - primary/secondary backlight Valid Input Threshold: Low <0.6 V Relay Outputs Quantity 3: 20 Amps, Quantity 7: 10 Amps (+V supplied) and Quantity 2: 10 Amps (+V supplied or dry contact selectable)

(ENG)

Brand

SoundOff Signal

Voltage

10-16

Components

100 Watt Siren, 100 Watt Siren/Switch Module, 200 Watt Siren / Switch Module, Central Controller, Control Panel, Input Node, Remote Node

Warranty

5 Years except 400 Series Siren/Switch Module (3Yrs)

SKU ENG

Data Sheet:

Click Here

Data Sheet:

Click Here

Data Sheet:

Click Here

Be The First To Review This Product!

Help other ozled users shop smarter by writing reviews for products you have purchased.

Write a product review